Tsubaki 41B15FL Finished Bore Sprocket, Single Strand, Inch, #41 ANSI No., 1/2" Pitch, 15 Teeth, 3/4" Bore

Tsubaki 41B15FL Finished Bore Sprocket, Single Strand, Inch, #41 ANSI No., 1/2" Pitch, 15 Teeth, 3/4" Bore

This Tsubaki roller chain sprocket has a 1/2-inch pitch, fits size 41 chains, and is single strand with one set of teeth around its circumference for use with single strand chains. It is a Type B sprocket with a hub projection encircling the bore on one side and is ready for installation on a shaft of the appropriate diameter. The teeth of the sprocket help prevent slipping and binding to avoid power loss in assemblies. It meets International Organization for Standardization (ISO) 9001 for quality assurance. This single strand roller chain sprocket is suitable for use in a broad range of applications involving light to moderate loads and ongoing, high-cycle operations, including vehicle transmission systems, construction and agricultural equipment, conveyors, and factory manufacturing and assembly lines, among others.A roller chain sprocket is a thin wheel with deep, uniformly spaced teeth ringing its circumference. The distance from the peak of one tooth to the next is called the pitch, and is commonly measured in 1/8-inch increments. The sprocket transfers power and motion by a roller chain that is threaded over the teeth of the sprocket. The alignment of the chain with the sprocket's pitch prevents the chain from slipping so that no power is lost. In the center of the sprocket is the bore (hole) for sliding the sprocket onto a shaft, and a bushing or bearing is often fitted to the sprocket’s hub to custom-fit the sprocket onto a shaft to hold it firmly in place. A hub is a protruding, raised lip encircling the bore of the sprocket. Sprockets with hubs on both sides are Type C, sprockets with hubs on one side are Type B, and sprockets with no hubs are Type A sprockets. For applications requiring sprockets to be swapped onto shafts of different diameters, a sprocket with a bore large enough to fit all shafts can be used, with the gap between the bore and shaft closed with a bushing or bearing. Roller chain sprockets are used in a broad range of applications where... [Read More]

  • UPC: 097039322210
  • ASIN: B002KU0GI4
  • Brand: Tsubaki
  • Manufacturer: Tsubaki

TruBind 10-mm (3/8-inch) Binding Coils - COIL10 - Durable - 4:1 Pitch (4 Holes/inch) - 12 Inches Long - Pre-Sized to Fit Letter-Sized Paper - Compatible with TruBind Binding Machines - 100 per Box

TruBind 10-mm (3/8-inch) Binding Coils - COIL10 - Durable - 4:1 Pitch (4 Holes/inch) - 12 Inches Long - Pre-Sized to Fit Letter-Sized Paper - Compatible with TruBind Binding Machines - 100 per Box

Every in-office binding project needs the perfect binding supplies to make it complete. TruBind 10-mm (3/8-inch) Binding Coils allow you to create professional-looking bound projects affordably and easily. Spiral coil binding offers documents both a professional, finished look and a lay-flat design with the ability to flip pages 360° from front to back. These plastic coils are an excellent high-quality choice for business proposals, directories, staff handbooks, annual reports, company presentations, restaurant menus, and more! Plastic spiral coils from TruBind are made of high-quality plastic that wont bend or snag. Each coil is pre-cut to 12 inches long, making them the perfect choice for binding spines for standard letter-sized documents. Plenty of excess is included so that you can crimp the ends for a finished look or simply trim them down if you need a slightly smaller size. TruBind plastic coils can be used with any binding machine with disengaging pins like all our TruBind machines. Each TruBind Binding Coil is 10 mm, or 3/8 inch in diameter, with 48 loops per 12-inch coil. This provides the right durability and holding strength for most in-office binding projects. All standard TruBind binding coils have a 4:1 pitch, which means they will fit any binding machine that punches 4 holes per inch. TruBind Plastic Binding Coils provide the flexibility you need to create affordable in-office projects. Our plastic coils can hold up to 75 sheets of standard 20# copy paper when bound. That equals a maximum binding capacity of 11/32 inches of thickness, perfect for most office projects. With 100 pieces per box, you can access wholesale binding-material pricing while purchasing the right number of coils for your office needs. Whether you are binding a few books or hundreds, TruBind provides the quality of materials you need.

  • UPC: 742415918494
  • ASIN: B003ODE97K
  • Brand: TruBind
  • Manufacturer: TruBind

Screw Chek'r SAE/ Inch Screw Thread Size Gauge (No. 1 to 5/16) 1/8 Inch Heavy Gauge Steel Screw Checker, Made in USA

Screw Chek'r SAE/ Inch Screw Thread Size Gauge (No. 1 to 5/16) 1/8 Inch Heavy Gauge Steel Screw Checker, Made in USA

The SAE/ Inch Screw Checker is a precision threaded tool for complete instant identification of both coarse and fine thread metric screws. This quality tool made of heavy gauge steel is satin chrome plated, expertly machined and American made. All do it yourselfers, handymen, mechanics and maintenance people have too often experienced the frustration and loss of valuable time and money by mistakenly identifying a screw. With this easy to use, pocket sized tool you can kiss those problems goodbye. No more headaches, cursing, and multiple trips to the hardware store. Unlike their plastic counterparts, these screw checkers, made of heavy gauge steel, will last for a very long time without the worry of wearing out the threads after a few uses.

  • UPC: 082045098785
  • ASIN: B0006NFUJW
  • Brand: Ruelle
  • Manufacturer: Ruelle

ChromaCast Guitar Pitch Pipe, inch (CC-GPP)

ChromaCast Guitar Pitch Pipe, inch (CC-GPP)

ChromaCast Guitar Pitch Pipe. ChromaCast is dedicated to crafting roadworthy products, and providing the best in creative design and durability. ChromaCast proves you don't have to spend a fortune for quality music gear.

  • UPC: 811501069737
  • ASIN: B01L3M83OI
  • Brand: ChromaCast
  • Size: -inch
  • Manufacturer: ChromaCast

Johnson Level 750 Pitch & Angle Locator in Degrees and Inch Rise per Foot Run

Johnson Level 750 Pitch & Angle Locator in Degrees and Inch Rise per Foot Run

Johnson Level 750 Pitch & Angle Locator in Degrees and Inch Rise per Foot RunMade of durable abs plastic; used to obtain or transferr any angle or pitch. Reads 0 to 90 degrees in 2 quadrants. Reads pitch or slope in inches per foot; printed scale to read pitch in inch rise per 12" run without the use of conversion tables.503977

  • UPC: 752913201257
  • ASIN: B01E6JRZZ8
  • Brand: Johnson Pitch
  • Manufacturer: Johnson Level

Horizontal Bolt and Nut Gauge / Thread Checker (Inch & Metric)

Horizontal Bolt and Nut Gauge / Thread Checker (Inch & Metric)

The Hillman Horizontal Bolt & Nut Gauge will help you quickly identify the most common size nuts & bolts in one compact and easy-to-use check center. Now you can know with certainty what size bolt or nut you have in your hand. No more guessing! Also known as a Thread Verifier or Thread Identifier, the Bolt & Nut Gauge is a must have for any shop, garage, or manufacturing facility. The Gauge has 26 female threaded holes (12 metric and 14 standard) for checking bolts or screws, and 26 male threaded studs (12 metric and 14 standard) to identify nut sizes. The bottom edge includes both a metric and standard (fractional) scale for checking diameter & length. It is made from 19" long by 3-1/2" wide by 1/4" thick annodized aluminum plate. It includes a pair of angle brackets and is pre-drilled for easy installation on a work bench or wall.

  • UPC: 798167987066
  • ASIN: B00OM1HUJ2
  • Brand: The Hillman Group
  • Manufacturer: The Hillman Group

MacGregor X52RE ASA Slow Pitch Composite Softball, 12-inch - One Dozen

MacGregor X52RE ASA Slow Pitch Composite Softball, 12-inch - One Dozen

These MacGregor X52RE ASA Slow Pitch 12" Softball is one of the best balls on the market and you will not go wrong with this purchase.

  • UPC: 842569089801
  • ASIN: B00HQK5M0U
  • Brand: MacGregor
  • Size: 12-Inch
  • Manufacturer: Sport Supply Group, Inc.

2 Pack Thread Pitch Gauge Stainless Steel Screw Pitch Measuring Tool (One America SAE Type and One Metric&Inch Type)

2 Pack Thread Pitch Gauge Stainless Steel Screw Pitch Measuring Tool (One America SAE Type and One Metric&Inch Type)

Product Description: --Product Material:Stainless Steel --Type: America SAE (51 pcs):60 * 60mm/2.36 * 2.36" Metric+Inch (52pc): 67 * 20mm/2.63 * 0.78" --Measuring rang: 0.25 - 6.00mm/0.0098" - 0.23" 51 pcs 60°US: 4,4.5,5,5.5,6,7,8,9,10,11,11.5,12,13,14,15,16,18,20,22,24,26,27,28,30,32,34,36,38,40,42,44,46,48,50,52,54,56,58,60,62,64,66,68,70,72,74,76,78,80,82,84 52pcs Metric/Inch: 60°Metric:0.25,0.3,0.35,0.4,0.45,0.5,0.6,0.7,0.75,0.8,0.9,1.0,1.25,1.5,1.75,2.0,2.5,3.0,3.5,4.0,4.5,5.0,5.5,6.0 55° Inch:4G,4-1/2G,5G,6G,7G,8G,9G,10G,11G,12G,13G,14G,16G,18G,19G,20G,22G,24G, 25G,26G,28G,30G,32G,36G,40G,48G,60G,62G Package includes: 1 xAmerica SAE type Thread Measuring Gage 1 xMetric and Inch type Thread Measuring Gage

  • UPC: 704529777633
  • ASIN: B07CXR627D
  • Brand: Singring
  • Manufacturer: Singring

Dudley ASA SBC Leather11-Inch Yellow Fast Pitch Softball, .47/375-Pounds, Red Stitch ( Pack of 12)1 Dozen

Dudley ASA SBC Leather11-Inch Yellow Fast Pitch Softball, .47/375-Pounds, Red Stitch ( Pack of 12)1 Dozen

Dudley ASA SBC Leather 11" Yellow Fast Pitch Softball

  • UPC: 689344395142
  • ASIN: B00192LV2E
  • Brand: Dudley
  • Size: 11-Inch
  • Manufacturer: Dudley

TruBind 6-mm (1/4-inch) Binding Coils - COIL06 - Durable - 4:1 Pitch (4 Holes/inch) - 12 Inches Long - Pre-Sized to Fit Letter-Sized Paper - Compatible with TruBind Binding Machines - 100 per Box

TruBind 6-mm (1/4-inch) Binding Coils - COIL06 - Durable - 4:1 Pitch (4 Holes/inch) - 12 Inches Long - Pre-Sized to Fit Letter-Sized Paper - Compatible with TruBind Binding Machines - 100 per Box

Every in-office binding project needs the perfect binding supplies to make it complete. TruBind 6-mm (1/4-inch) Binding Coils allow you to create professional-looking bound projects affordably and easily. Spiral coil binding offers documents both a professional, finished look and a lay-flat design with the ability to flip pages 360° from front to back. These plastic coils are an excellent high-quality choice for business proposals, directories, staff handbooks, annual reports, company presentations, restaurant menus, and more! Plastic spiral coils from TruBind are made of high-quality plastic that wont bend or snag. Each coil is pre-cut to 12 inches long, making them the perfect choice for binding spines for standard letter-sized documents. Plenty of excess is included so that you can crimp the ends for a finished look or simply trim them down if you need a slightly smaller size. TruBind plastic coils can be used with any binding machine with disengaging pins like all our TruBind machines. Each TruBind Binding Coil is 6 mm, or 1/4 inch in diameter, with 48 loops per 12-inch coil. This provides the right durability and holding strength for most in-office binding projects. All standard TruBind binding coils have a 4:1 pitch, which means they will fit any binding machine that punches 4 holes per inch. TruBind Plastic Binding Coils provide the flexibility you need to create affordable in-office projects. Our plastic coils can hold up to 30 sheets of standard 20# copy paper when bound. That equals a maximum binding capacity of 3/16 inches of thickness, perfect for most office projects. With 100 pieces per box, you can access wholesale binding-material pricing while purchasing the right number of coils for your office needs. Whether you are binding a few books or hundreds, TruBind provides the quality of materials you need.

  • UPC: 742415918456
  • ASIN: B003ODCSP0
  • Brand: TruBind
  • Manufacturer: TruBind