HiLetgo 3pcs Pro Micro Atmega32U4 5V 16MHz Bootloadered IDE Micro USB Pro Micro Development Board Microcontroller Compatible to Arduino Pro Micro Serial Connection with Pin Header
HiLetgo 3pcs Pro Micro Atmega32U4 5V 16MHz Bootloadered IDE Micro USB Pro Micro Development Board Microcontroller Compatible to Arduino Pro Micro Serial Connection with Pin Header
Description: 1. The Pro Micro is similar to the Pro mini except with a ATmega32U4 on board. The USB transceiver inside the 32U4 allows us to add USB connectivity on board and do away with bulky external USB interface. 2. This tiny little board does all of the neat-o Arduino tricks that you're familiar with: 4 channels of 10-bit ADC, 5 PWM pins, 12 DIOs as well as hardware serial connections Rx and Tx. Running at 16MHz and 5V, this board will remind you a lot of your other favorite Arduino-compatible boards but this little guy can go just about anywhere. If you're supplying unregulated power to the board, be sure to connect to the "RAW" pin on not VCC. Features: ATmega32U4 running at 5V/16MHz Supported by Arduino IDE v1.0.1 On-Board Micro-USB connector for programming 4 x 10-bit ADC pins, 12 x Digital I/Os Rx and Tx Hardware Serial Connections Note: 1.When you open the Arduino IDE software, pls go to the tool and choose the board "Arduino Leonardo" 2.The acceptable voltage range is 5 to 9 V.Package included: 3* Pro Micro ATmega32U4 5V/16MHz Development Board
- ASIN: B01MTU9GOB
- Brand: HiLetgo
- Size: Small
- Manufacturer: HiLetgo®
ATtiny85 Microcontroller, 8-pin PDIP
ATtiny85 Microcontroller, 8-pin PDIP
ATtiny85 Microcontroller, 8-pin PDIP The ATtiny85 is a low-power CMOS 8-bit microcontroller based on the AVR enhanced RISC architecture. By executing powerful instructions in a single clock cycle, the ATtiny85 achieves throughputs approaching 1 MIPS per MHz allowing the system designer to optimize power consumption versus processing speed. Key Parameters Flash (Kbytes): 8 Kbytes Pin Count: 8 Max. Operating Frequency: 20 MHz Power Supply: 2.7 - 5.5V Operational Range: Industrial (A) (-40°C to 85°C) CPU: 8-bit AVR # of Touch Channels: 3 Hardware QTouch Acquisition: No Max I/O Pins: 6 Ext Interrupts: 6 USB Speed: No USB Interface: No
- UPC: 013564018640
- ASIN: B00C9NXO9A
- Brand: ATMEL SEMICONDUCTOR
- Manufacturer: ATMEL SEMICONDUCTOR
Microchip PIC18F452-I/P Microcontroller, 8-Bit, 32KB Flash, Plastic Dip Tube, 40-Pin, 5 Volt, 52.26 mm L x 13.84 mm W x 3.81 mm H
Microchip PIC18F452-I/P Microcontroller, 8-Bit, 32KB Flash, Plastic Dip Tube, 40-Pin, 5 Volt, 52.26 mm L x 13.84 mm W x 3.81 mm H
The product type is Microchip PIC18F452-I/P Microcontroller, 8-Bit, 32KB Flash, Plastic Dip Tube, 40-Pin, 5 Volt, 52.26 mm L x 13.84 mm W x 3.81 mm H. Made in Taiwan and manufactured by Microchip Corporation.
- UPC: 738878252411
- ASIN: B00B8867AK
- Brand: MICROCHIP
- Manufacturer: Microchip Corporation
WINGONEER 4-Digit DIY LED Electronic Clock Kit Microcontroller 0.8inch Digital Tube Clock with Thermometer Hourly Chime Function DIY Kit Module - Green
WINGONEER 4-Digit DIY LED Electronic Clock Kit Microcontroller 0.8inch Digital Tube Clock with Thermometer Hourly Chime Function DIY Kit Module - Green
WINGONEER trademark Reg.NO:4747611WINGONEER 4-Digit DIY LED Electronic Clock Kit Microcontroller 0.8inch Digital Tube Clock with Thermometer Hourly Chime Function DIY Kit Module This is a quite fantastic DIY electronic clock. Based on micro controller, IC board and some electronic components, you can easily assemble and solder it quickly. With digital tube, you can watch time clearly no matter day time or at night. It is suitable for DIY enthusiasts, school training lessons etc. Why not not come and purchase oneFeatures:With written program, you can use it directly.Based on micro controller, precise timekeeping and mini in size.Easy to set & adjust hour, minute, second ,date, week and hourly chime.Can be used as thermometer to test and display temperature per 30sec.Light control, the clock will automatically be brighter during the day than the night.With transparent case, components can be well protected and the clock looks stylish.Perfect for electronic DIY enthusiasts, school training lessons etc.Note1. It can work when blackout with a 3V lithium battery.(not included)2. You need to solder it yourself.3. Since its working voltage is DC 5V, thus can be powered through phone charger with a USB wire. 4. For more specific function and application method, please read our English user manual.SpecificationsColor Blue Green White Red (optional)Display 4-digit LEDPower Supply 3V CR1220 Button Battery (not included)Working Voltage DC 5VWorking Current 40mAClock Size 7 2.5 1.2cm 2.76 0.98 0.47inIC Board Size 7.2 2.7cm 2.84 1.06in Kit Weight 82g 2.9ozPackage Size 12 8.5 3.5cm 4.72 3.35 1.38inPackage Weight 85.5g 3.01ozPackage List1 x DIY Electronic Clock Kit(Battery not Included)
- UPC: 662578904908
- ASIN: B06XBDYCQ2
- Brand: WINGONEER
- Manufacturer: WINGONEER
KeeYees Pro Micro ATmega32U4 5V 16MHz Micro USB Development Board Module Microcontroller for Arduino IDE Leonardo Bootloader (Pack of 3pcs)
KeeYees Pro Micro ATmega32U4 5V 16MHz Micro USB Development Board Module Microcontroller for Arduino IDE Leonardo Bootloader (Pack of 3pcs)
Features: ATmega32U4 running at 5V/16MHz Supported under Arduino IDE v1.0.1 Recommend power supply for board: 6-7V, less than 9V On-Board micro-USB connector for programming 4 x 10-bit ADC pins, 12 x Digital I/Os Rx and Tx Hardware Serial Connections How to use? 1. Connected to computer. 2 Opened Arduino IDE and loaded Blink sketch. 3. Set board to Leonardo and selected the appropriate COM port (It showed up in the list already identified as a Leonardo). 4. Connected an LED to pin 9 and modified the sketch accordingly. 5. Hit upload and within a few seconds having a blinking LED. Package Includes: 3 x Pro Micro ATmega32U4 5V 16MHz Module for Arduino
- UPC: 705883356052
- ASIN: B07FXCTVQP
- Brand: KeeYees
- Size: Pack of 3pcs
- Manufacturer: KeeYees
Microchip PIC16F84A-04/P Microcontroller Unit, DIP-18, 1K, Flash, 4 MHz, 13 I/O, C-Temp, 6.35 mm W x 3.3 mm H x 22.86 mm L (Pack of 2)
Microchip PIC16F84A-04/P Microcontroller Unit, DIP-18, 1K, Flash, 4 MHz, 13 I/O, C-Temp, 6.35 mm W x 3.3 mm H x 22.86 mm L (Pack of 2)
Microchip PIC16F84A-04/P Microcontroller Unit, Dip-18, 1K, Flash, 4 MHz, 13 I/O, C-Temp, 6.35 mm W x 3mm H x 22.86 mm L (Pack of 2), 6.35 millimeters width, 22.86 millimeters Length, Volts (Pack of 2). Product type - microcontroller. Pin count -18. Supplier package - pdip. Microchip PIC16F84A-04/P Microcontroller Unit, Dip-18, 1K, Flash, 4 MHz, 13 I/O, C-Temp, 6.35 mm W x 3mm H x 22.86 mm L (Pack of 2), 6.35 millimeters width, 22.86 millimeters Length, Volts (Pack of 2). Unit Count : Microcontroller.
- ASIN: B01N3ALV49
- Brand: MICROCHIP
- Manufacturer: Microchip Corporation
5x V3.0 USB Nano ATmega328P 5V 16M Micro controller Board Module Arduino TE359
5x V3.0 USB Nano ATmega328P 5V 16M Micro controller Board Module Arduino TE359
Description: CH340G Replace FT232RL Operating Voltage(logic level): 5V 8 analog inputs ports: A0 ~ A7 14 Digital input / output ports:TX,RX,D2 ~ D13 6 PWM ports: D3, D5, D6, D9, D10, D11 1 pairs of TTL level serial transceiver ports RX / TX Using Atmel Atmega328P-AU MCU There is bootloader installed in it Support USB download and Power Support for external 5V ~ 12V DC power supply Support power supply by 9V battery Package included 5x Mini USB Nano V3.0 ATmega328P 5V 16M Micro Controller Board For Arduino
- ASIN: B015MGHH6Q
- Brand: XCSOURCE
- Size: Edition2
- Manufacturer: XCSOURCE
Serveyou ATmega32U4 5V 16MHz Micro USB Development Board Module Microcontroller for Arduino with The Bootloader Replace for Arduino (1pc/3pcs)(3pcs)
Serveyou ATmega32U4 5V 16MHz Micro USB Development Board Module Microcontroller for Arduino with The Bootloader Replace for Arduino (1pc/3pcs)(3pcs)
Features: ATmega32U4 running at 5V/16MHz.Supported by for Arduino IDE v1.0.1.On-Board Micro-USB connector for programming.4 x 10-bit ADC pins, 12 x Digital I/Os.Rx and Tx Hardware Serial Connections.Specifications:Size:Approx.33.1x17.9mmQuantity:1pc/3pcsPackage included: 1pc/3pcs x Pro Micro ATmega32U4 5V/16MHz Development BoardNote: 1.When you open the for Arduino IDE software, pls go to the tool and choose the board "for Arduino Leonardo".2.Due to the light and screen difference, the item's color may be slightly different from the pictures.3.Please allow 0.5-2 cm differences due to manual measurement.
- UPC: 697183995362
- ASIN: B07RL2BW4F
- Brand: Serveyou
- Size: 3pcs
- Manufacturer: Serveyou
Walmeck 4-Digit DIY LED Electronic Clock Kit Microcontroller 0.8inch Digital Tube Clock with Thermometer Hourly Chime Function DIY Kit Module
Walmeck 4-Digit DIY LED Electronic Clock Kit Microcontroller 0.8inch Digital Tube Clock with Thermometer Hourly Chime Function DIY Kit Module
This is a quite fantastic DIY electronic clock. Based on micro controller, IC board and some electronic components, you can easily assemble and solder it quickly. With digital tube, you can watch time clearly no matter day time or at night. It is suitable for DIY enthusiasts, school training lessons etc. Why not not come and purchase one?Features： With written program, you can use it directly. Based on micro controller, precise timekeeping and mini in size. Easy to set & adjust hour, minute, second ,date, week and hourly chime. Can be used as thermometer to test and display temperature per 30sec. Light control, the clock will automatically be brighter during the day than the night. With transparent case, components can be well protected and the clock looks stylish. Perfect for electronic DIY enthusiasts, school training lessons etc.Note: 1. It can work when blackout with a 3V lithium battery.(not included) 2. You need to solder it yourself. 3. Since its working voltage is DC 5V, thus can be powered through phone charger with a USB wire. 4. For more specific function and application method, please read our English user manual.Specifications: Color: Blue / Green / White / Red (optional) Display: 4-digit LED Power Supply: 3V CR1220 Button Battery (not included) Working Voltage: DC 5V Working Current: 40mA Clock Size: 7 * 2.5 * 1.2cm / 2.76 * 0.98 * 0.47in IC Board Size: 7.2 * 2.7cm / 2.84 * 1.06in Kit Weight: 82g / 2.9oz Package Size: 12 * 8.5 * 3.5cm / 4.72 * 3.35 * 1.38in Package Weight: 85.5g / 3.01ozPackage List: 1 * DIY Electronic Clock Kit(Battery not Included) 1 * User Manual(English)
- ASIN: B079QLJF36
- Brand: Walmeck
- Manufacturer: Walmeck
Mini Nano V3.0 ATmega328P Microcontroller Board USB Cable for Arduino
Mini Nano V3.0 ATmega328P Microcontroller Board USB Cable for Arduino
Features: Nano V3.0 ATmega328P Microcontroller Board w/USB Cable For Arduino Fully Compatible to Arduino Nano V3.0 ATmega328P-AU ATmega328 Microcontroller Bootloader installed, ready to upload sketches from Arduino software Microcontroller ATmega328P-AU Operating Voltage :5V Input Voltage (recommended) 7V-12V Input Voltage (limits) 6V-20V Digital I/O Pins 14 (of which 6 provide PWM output) Analog Input Pins 8 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 32 KB (ATmega328) of which 2 KB used by bootloader SRAM 2 KB EEPROM 1 KB Clock Speed 16 MHz Dimention:Approx. 45x17x19mm Cable Length:245mm Color:Blue(as the picture shows) Package: 1 xNano V3.0 ATmega328P Arduino Compatible Board 1 xMini USB Cable
- UPC: 889736744767
- ASIN: B00NLAMS9C
- Brand: Makerfire
- Manufacturer: Elisona