Adafruit Motor/Stepper/Servo Shield for Arduino v2.3 Kit
Adafruit Motor/Stepper/Servo Shield for Arduino v2.3 Kit
We have upgraded the shield kit to make the bestest, easiest way to drive DC and Stepper motors. This shield will make quick work of your next robotics project! We kept the ability to drive up to 4 DC motors or 2 stepper motors, but added many improvements: Lots of other little improvements such as a polarity protection FET on the power pins and a bit of prototyping area. And the shield is assembled and tested here at Adafruit so all you have to do is solder on straight or stacking headers and the terminal blocks. Lets check out these specs again: 2 connections for 5V 'hobby' servos connected to the Arduino's high-resolution dedicated timer - no jitter! 4 H-Bridges: TB6612 chipset provides 1.2A per bridge (3A peak) with thermal shutdown protection, internal kickback protection diodes. Can run motors on 4.5VDC to 13.5VDC. Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5% resolution) Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil, interleaved or micro-stepping. Motors automatically disabled on power-up Big terminal block connectors to easily hook up wires (18-26AWG) and power Arduino reset button brought up top Polarity protected 2-pin terminal block and jumper to connect external power, for separate logic/motor supplies Tested compatible with Arduino UNO, Leonardo, ADK/Mega R3, Due, Diecimila & Duemilanove. Works with Mega/ADK R2 and earlier with 2 wire jumpers. Download the easy-to-use Arduino software library, check out the examples and you're ready to go! New! As of 3/21/2014 we are shipping motor shields with the terminal blocks, and power jumper pre-soldered on. You'll still need to do a little soldering to put on the shield-headers (or stacking headers) but it should be even easier and faster to get started!
- UPC: 702658303396
- ASIN: B00PUTH3B0
- Brand: Adafruit
- Manufacturer: Adafruit
SunFounder Ethernet Shield W5100 for Arduino UNO R3 Mega 2560 1280 A057
SunFounder Ethernet Shield W5100 for Arduino UNO R3 Mega 2560 1280 A057
Features 1.With this Ethernet Shield, your Arduino board can be used to connect to internet. 2.Can be used as server or client. 3.Directly plug puzzle board, no soldering required. 4.Controller: w5100. 5.This is the latest version of the Ethernet Shield. 6.This Arduino Ethernet Shield which is based on the Wiznet W5100 Ethernet Chip gives you an easy way to get your Arduino Online. 7.It is directly supported by Arduino official Ethernet Library. 8.It adds a micro-SD card slot, which can be used to store files for serving over the network. 9.It is compatible with the Arduino Duemilanove (168 or 328), Uno as well as Mega (1280/2560) and can be accessed using the SD library. 10.The Wiznet W5100 provides a network (IP) stack capable of both TCP and UDP. 11.It supports up to four simultaneous socket connections. 12.Use the Ethernet library to write sketches which connect to the internet using the shield. 13.Fits all version of arduino Main board,2009,UNO, mega 1280, mega 2560. 14.Size:7cm x 5.4cm x 2.4cm - 2.76inch x 2.12inch x 0.94inch. Package Included 1 x Ethernet Shield
- UPC: 611326263354
- ASIN: B00HG82V1A
- Brand: SunFounder
- Manufacturer: SunFounder
RoboGets Ethernet Shield for Arduino Uno r3 and Mega, Network Expansion Shield Board with Micro SD Card Slot Support
RoboGets Ethernet Shield for Arduino Uno r3 and Mega, Network Expansion Shield Board with Micro SD Card Slot Support
RoboGets Ethernet Shield for Arduino Uno r3 and Mega
- UPC: 657819001577
- ASIN: B07G3G1CKF
- Brand: RoboGets
- Size: Edition51 Ethernet Shield
- Manufacturer: RoboGets
ACROBOTIC WeMos ESP8266 D1 Mini DHT-11 Temperature/Humidity Sensor Shield for Arduino NodeMCU Raspberry Pi Wi-Fi IoT DHT-22 DHT11 DHT22
ACROBOTIC WeMos ESP8266 D1 Mini DHT-11 Temperature/Humidity Sensor Shield for Arduino NodeMCU Raspberry Pi Wi-Fi IoT DHT-22 DHT11 DHT22
The WeMos D1 Mini family of boards is one of the latest additions to the ESP8266-based IoT ecosystem. The WeMos D1 Mini DHT-11 Temperature/Humidity Sensor Shield includes the popular sensor for measuring temperature and relative humidity locally. The WeMos D1 Mini DHT-11 Temperature/Humidity Sensor Shield is designed so that pin D4 on the WeMos D1 Mini v2 board is connected to the data pin of the sensor. This means that you'll need to configure your software to use pin D4. There are plenty of existing libraries to work with this sensor especially if you're using the Arduino Software. This inexpensive sensor is a great way to get temperature and humidity data, as it only uses one pin from the microcontroller or SoC. What makes the WeMos family of development boards for the ESP8266 great is the availability of stackable, plug-and-play shields such as this WeMos D1 Mini DHT-11 Temperature/Humidity Sensor Shield. Without much fuss, it's very easy to connect, control, and monitor a wide variety of electronic components to the ESP8266. The WeMos family is a great solution for building projects quickly using the ESP8266 SoC. Different users have different applications for the WeMos shields, thus we've found that the easiest way to please everyone is to ship the boards with the headers unsoldered. Each board in this kit includes a pair of Male, Female, Long Female pin headers for you to choose. Soldering is required for installing the header pins! Features: DHT-11 measurement range: 20~95%RH; 0~50°C DHT-11 data pin connected to pin D4 Breaks out all the WeMos pins for easy access when stacked on top of/below the WeMos D1 Mini v2 We have written useful guides for getting you started with the WeMos D1 Mini DHT-11 Temperature/Humidity Sensor Shield:http://learn.acrobotic.com/tutorials/post/wemos-d1-mini-dht-11-shield
- UPC: 769748350890
- ASIN: B07G2VZJNY
- Brand: ACROBOTIC
- Size: Temperature and Humidity
- Manufacturer: ACROBOTIC Industries
HiLetgo L293D Motor Driver Shield Compatible to Duemilanove Mega UNO R3 AVR ATMEL
HiLetgo L293D Motor Driver Shield Compatible to Duemilanove Mega UNO R3 AVR ATMEL
Features: 1. to 4 bidirectional DC motors and 4 PWM speed controllers (approximately 0.5% resolution) 2. Up to 2 stepper motor forward and reverse control, single / double step control, staggered or micro-step and rotation angle control 3. 4-way H-bridge: The L293D chip provides 0.6A (peak 1.2A) current per bridge with thermal shutdown protection, 4.5Vto36V 4. The pull-down resistor ensures that the motor remains stopped at power-up 5. Large terminal blocks make wiring easier (10-22AWG) and power 6. With reset button 7. 2 large terminal external power terminals, to ensure logic and motor drive power separation 8. Download Easy to use software library for rapid project development Package Included: 1*L293D Motor Driver Shield
- UPC: 702082656945
- ASIN: B01DG61YRM
- Brand: HiLetgo
- Size: Small
- Manufacturer: HiLetgo
FTCBlock 4 Pieces Breadboards Kit with 120 Pieces Jumper Wires for Arduino Proto Shield Distribution Connecting Blocks
FTCBlock 4 Pieces Breadboards Kit with 120 Pieces Jumper Wires for Arduino Proto Shield Distribution Connecting Blocks
The breadboard is designed for the solderless experiment of electronic circuits because there are many small jacks on the board. Since various electronic components can be inserted or removed as needed, the welding is eliminated,the assembly time of the circuit is saved, and the components can be reused, so it is very suitable for assembly, debugging and training of electronic circuits. 400 tie-points total. 300 tie-point IC-circuit area plus four 25 tie-point power rails 630 tie-point ic-circuit area plus 2x100 tie-point distribution strips providing 4 power rails White plastic, with black legend. Colored power rails 830 Points breadboard size: 6.5 x 2.1 x 0.3 inch/ 165 x 55 x 9 mm 400 Points breadboard size: 3.2 x 2.1 x 0.3 inch/ 82 x 55 x 9 mm For wires 21 to 26 AWG 2-sidedpeelable adhesive tape Board Material: White ABS plastic with black legend. Internal Contacts Material: Phosphor bronze finished. Board Base: Self-Adhesive Tape Package included - 2pcs 830 points breadboards - 2pcs 400 points breadboards - 40pcs male-male jumper wires - 40pcs male-female jumper wires - 40pcs female-female jumper wires
- UPC: 729043078950
- ASIN: B07H326BFQ
- Brand: FTCBlock
- Manufacturer: Southern Tech
DJ Shield for Arduino (Standard knobs)
DJ Shield for Arduino (Standard knobs)
The DJ Shield shield for Arduino give you 5 high-quality buttons and 3 10K linear potentiometers to provide input to your projects. The DJ Shield was designed for use with the Audio Hacker shield but can be used in any Arduino project. 5 tactile buttons, connected to digital pins 2-6 3 10K linear potentiometers connected to analog pins 0,1,2. (shaft is 1/4") 2 LEDs (one red, one blue) connected to analog pins 4 and 5 (analog pins can also be used as digital pins) 3 ABS plastic knobs for the potentiometers. Easy to assemble kit! Also available in the Deluxe version which has fancy Aluminum knobs! Usage Guide Initialization pinMode(2, INPUT); pinMode(3, INPUT); pinMode(4, INPUT); pinMode(5, INPUT); pinMode(6, INPUT); digitalWrite(2, HIGH); digitalWrite(3, HIGH); digitalWrite(4, HIGH); digitalWrite(5, HIGH); digitalWrite(6, HIGH); pinMode(A4, OUTPUT); pinMode(A5, OUTPUT); Button Input // Read button D2: boolean d2Pressed = digitalRead(2); // Read button D5 (red button): boolean d5Pressed = digitalRead(5); Potentiometer Input // Read middle potentiometer: int a1 = analogRead(A1); LEDs // Turn on left LED digitalWrite(A4, HIGH); // Turn off right LED digitalWrite(A5, LOW);
- UPC: 602401813854
- ASIN: B01LX6NZ8E
- Brand: Nootropic Design
- Manufacturer: Nootropic Design
kuman CNC Shield Expansion Board V3.0 +UNO R3 Board + A4988 Stepper Motor Driver with Heatsink for Arduino Kits K75 (CNC Shield+UNO R3+Stepper Motor)
kuman CNC Shield Expansion Board V3.0 +UNO R3 Board + A4988 Stepper Motor Driver with Heatsink for Arduino Kits K75 (CNC Shield+UNO R3+Stepper Motor)
CNC Shield Board: Latest Arduino CNC Shield Version 3. 0 GRBL 0. 9 compatible 4-Axis support (X, Y, Z , A-Can duplicate X, Y, Z or do a full 4th axis with custom firmware using pins D12 and D13) 2 x End stops for each axis (6 in total) Coolant enable Compatible with A4988 or DRV8825 stepper driver Runs on 12-36V DC Arduino UNO R3 Board: MCU: ATmega328 USB interface: ATmega16U2 Operating voltage: 5V Digital I/O pins: 14 (including 6 with PWM capability) Analog input pins: 6 I-I/O pin output current: 40mA max 3. 3V output current: 150mA max Flash memory: 32 kB (0. 5kB used by bootloader - included) Static RAM (SRAM): 2 kB EEPROM: 1 kB Clock speed: 16MHz A4988 Stepper Motor Driver: A4988 Stepper Motor Driver Board is a breakout board for Allegro's A4988 DMOS Micro stepping Driver with Translator and Overcurrent Protection; Low RDS (On) Output Automatic current decay mode detection / selection Mix with slow current decay modes Synchronous rectification for low power dissipation Internal UVLO Crossover-current protection 3. 3 and 5 V compatible logic supply Thermal shutdown circuitry Ground fault protection Load short-circuit protection Five selectable step modes: full, 1/2, 1/4, 1/8 and 1/16 Warning: Connecting or disconnecting a stepper motor while the driver is powered can destroy the driver. (More generally, rewiring anything while it is powered is asking for trouble). Package Contents: 1 x CNC Shield Board 1 x UNO R3 Board for Arduino 4 x A4988 Stepper Motor Driver 4 x Heat Sink
- ASIN: B06XHKSVTG
- Brand: kuman
- Manufacturer: kuman
3G/GPRS/GSM Shield for Arduino with GPS - American version SIM5320A
3G/GPRS/GSM Shield for Arduino with GPS - American version SIM5320A
Descriptions: The Tinysine 3G Cellular Shield provides you a way to use the 3G/GSM cell phone network to receive data from a remote location. This 3G shield has better coverage, GSM backwards-compatibility and even sports a built-in GPS module for geolocation & asset tracking. This all-in-one cellular phone module with that lets you add location-tracking, voice, text, SMS and data to your project in a single shield. 3G/GPRS specifications: - Quad-band 850MHz GSM, 900MHz EGSM, 1800MHz DCS, 1900MHz PCs - connect onto any global GSM network with any 2G SIM - This is the American Version dual-band UMTS/HSDPA 850/1900MHz WCDMA + HSDPA - Fully-integrated GPS(Qualcomm PM8015 GPS) that can be controlled and query over the same serial port - Make and receive voice calls using a headset or an external 8Ω speaker + electret microphone - Send and receive SMS messages - Send and receive GPRS data(TCP/IP, HTTP, etc) - AT command interface can be used with 300, 600, 1200, 4800, 9600, 19200, 38400, 57600, 115200, 230K, 461K, 961K, 3.2M, 3.7M and 4.0Mbps - Native USB support - plug it into a computer and you'll get serial ports for AT commands, GPS NMEA as well as a modem (note we've only tried out the AT&NMEA ports on Windows)GPS specifications: - 16 acquisition channels - GPS L1 C/A code - Sensitivity Tracking: -157dBm / Cold starts : -144dBm -Time-To-First-Fix Cold starts: 100s(typ) / Hot starts: 1s(typ) - Accuracy: approx 2.5 meters
- UPC: 742010214755
- ASIN: B01HNV3ZXC
- Brand: TinySine
- Manufacturer: TinySine
Botletics SIM7000 LTE CAT-M1 NB-IoT Cellular + GPS + Antenna Shield Kit for Arduino (SIM7000A)
Botletics SIM7000 LTE CAT-M1 NB-IoT Cellular + GPS + Antenna Shield Kit for Arduino (SIM7000A)
Botletics™ SIM7000 Shield Kit This powerful cellular shield for Arduino supports the latest cutting-edge LTE CAT-M and NB-IoT technology as well as fast multi-GNSS positioning. Its ultra-low power consumption is perfect for battery- or solar-powered IoT devices and it's compatible with almost any microcontroller and development platform. Plug-in compatible with Arduino Uno/Mega/Leonardo and easy wiring for any 1.8-5V microcontroller like ESP8266, ESP32, and Raspberry Pi if wired externally Wiring documentation and Arduino code examples for AVR, ATSAMD21, ESP8266, and ESP32 LTE CAT-M1 and NB-IoT support. SIM7000C, SIM7000E, and SIM7000G versions additionally support 2G (GSM/GPRS) and 2.5G (EDGE) Uplink speed up to 375kbps, downlink up to 300kbps Several shield versions for different regions of the globe Ultra low power (7.4uA in lowest state with a 3.7V LiPo battery) On-board 3.7V LiPo battery charging Supports SMS, TCP/IP, PPP, and FTP/HTTP/SSL Integrated multi-GNSS (GPS, GLONASS) with 2.5 meter accuracy Built-in electronic file system (EFS) for saving data On-board MCP9808 I2C temperature sensor Micro USB for AT commands and diagnostics Extra I2C header for convenience SIM7000 module power and network status LEDs Convenient u.FL antenna connectors Additional notes: Full product documentation and example code found on Github: https://github.com/botletics/SIM7000-LTE-Shield How to get network connection: https://github.com/botletics/SIM7000-LTE-Shield/wiki/Connecting-to-Network This kit does not include a 3.7V LiPo battery or SIM card, which are required for proper operation SIM card must support LTE CAT-M or NB-IoT! The Hologram.io SIM card works great in the USA Stacking female headers require basic soldering
- ASIN: B07H3XKNLH
- Brand: Botletics
- Size: SIM7000A
- Manufacturer: Botletics