Autofu Universal Scissor Jack 2 Ton Wind Up Lift Floor Jacks 14 Inch Height with Crank Speed Handle Rust-Proof for Ford F-150 Chevrolet Toyota Dodge Ram
Autofu Universal Scissor Jack 2 Ton Wind Up Lift Floor Jacks 14 Inch Height with Crank Speed Handle Rust-Proof for Ford F-150 Chevrolet Toyota Dodge Ram
The scissor jack, with tooth gears, can extend from 90mm(close position) to 360mm, more than enough to lift most vehicles. Easy to operate using the chromed crank with speed handle. Condition: Brand new Minimum height: about 90MM Maximum height: approximately 360MM Lifting: 2.0T Material: Steel Net weight: 2.1KG Item Size: 35*8.5*8.5 (L×W×T) Scope: Suitable for small and medium sized vehicles. Such as: For cars/Buick/Santana/Vietnam and other vehicles. Packing include: Scissor jack * 1 Handle * 1 HEIGHT/CAPACITY CURVE This device is designed to sustain the following loads at these specified heights. DO NOT EXCEED the rated capacity for each position. Before Use: 1. Check before each use for abnormal conditions such as cracked welds, leaks, damaged, loose or missing parts. 2. Inspect the jack immediately if lift is believed to have been subjected to an abnormal load or shock. 3. If the jack is found to be damaged, it should be removed from service until properly repaired. OPERATING INSTRUCTIONS 1. Insert the jack handle into the hole of the handle socket. 2. Make sure that the saddle is correctly positioned. To prevent damage to the jack, do not move the jack while the handle is intact in the socket. 3. To raise load, use one hand to hold the front part of the handle and use the other hand to turn at the rear and of the handle clockwise. 4. To lower load, use one hand to hold the front part of the handle and use the other hand to turn at the rear and of the handle counterclockwise slowly. CARE AND MAINTENANCE: 1. When jack is not in use, lifting arm should be in full down position. 2. Always keep jack clean and keep the screw and bearings well lubricated. 3. Store the handle with care.
- UPC: 667673316120
- ASIN: B06ZY83PLD
- Brand: Autofu
- Size: Scissor Jack
- Manufacturer: Autofu
Autofu 2 Tonne Spare Tire Scissors Lift Jack with Crank Tool Rust-Proof for Toyota Corolla 1993/1994/1995/1996/1997
Autofu 2 Tonne Spare Tire Scissors Lift Jack with Crank Tool Rust-Proof for Toyota Corolla 1993/1994/1995/1996/1997
Condition: Brand new Minimum height: about 90MM Maximum height: approximately 360MM Lifting: 2.0T Material: Steel Net weight: 2.1KG Item Size: 35*8.5*8.5 (L×W×T) Scope: Suitable for small and medium sized vehicles. Such as: For cars/Buick/Santana/Vietnam and other vehicles. Packing include: Scissor jack * 1 Handle * 1 HEIGHT/CAPACITY CURVE This device is designed to sustain the following loads at these specified heights. DO NOT EXCEED the rated capacity for each position. Before Use: 1. Check before each use for abnormal conditions such as cracked welds, leaks, damaged, loose or missing parts. 2. Inspect the jack immediately if lift is believed to have been subjected to an abnormal load or shock. 3. If the jack is found to be damaged, it should be removed from service until properly repaired. OPERATING INSTRUCTIONS 1. Insert the jack handle into the hole of the handle socket. 2. Make sure that the saddle is correctly positioned. To prevent damage to the jack, do not move the jack while the handle is intact in the socket. 3. To raise load, use one hand to hold the front part of the handle and use the other hand to turn at the rear and of the handle clockwise. 4. To lower load, use one hand to hold the front part of the handle and use the other hand to turn at the rear and of the handle counterclockwise slowly. CARE AND MAINTENANCE: 1. When jack is not in use, lifting arm should be in full down position. 2. Always keep jack clean and keep the screw and bearings well lubricated. 3. Store the handle with care.
- UPC: 667673317844
- ASIN: B06Y65Z3B9
- Brand: Autofu
- Size: 2TON Scissor Jack
- Manufacturer: Autofu
DICN Scissor Jack with Crank Handle Car Tire Repair Kit Emergency for Toyota Camry Corolla Prius Vios - 2 Ton/ 4.2-15 Inch
DICN Scissor Jack with Crank Handle Car Tire Repair Kit Emergency for Toyota Camry Corolla Prius Vios - 2 Ton/ 4.2-15 Inch
Package included: Scissor jack x 1 Handle x 1 Specification: Condition: Brand new Minimum height: about 105MM Maximum height: approximately 385MM Lifting: 2T Color: Black Material: Steel Net weight: 2.1KG Item Size: 41*8.8*9 CM HEIGHT/CAPACITY CURVE This device is designed to sustain the following loads at these specified heights. DO NOT EXCEED the rated capacity for each position. Before Use 1. Check before each use for abnormal conditions such as cracked welds, leaks, damaged, loose or missing parts. 2. Inspect the jack immediately if lift is believed to have been subjected to an abnormal load or shock. 3. If the jack is found to be damaged, it should be removed from service until properly repaired. OPERATING INSTRUCTIONS 1. Insert the jack handle into the hole of the handle socket. 2. Make sure that the saddle is correctly positioned. To prevent damage to the jack, do not move the jack while the handle is intact in the socket. 3. To raise load, use one hand to hold the front part of the handle and use the other hand to turn at the rear and of the handle clockwise. 4. To lower load, use one hand to hold the front part of the handle and use the other hand to turn at the rear and of the handle counterclockwise slowly. CARE AND MAINTENANCE 1. When jack is not in use, lifting arm should be in full down position. 2. Always keep jack clean and keep the screw and bearings well lubricated. 3. Store the handle with care.
- UPC: 783057938358
- ASIN: B073CMLYTJ
- Brand: DICN
- Manufacturer: DICN Factory
DICN Steel Scissor Jack Black Rustproof 2 Ton Capacity/385mm Max.Height with Chromed Speed Crank Handle Tire Changing Tools for Car Van Truck Vehicles, 1PCs US Ship
DICN Steel Scissor Jack Black Rustproof 2 Ton Capacity/385mm Max.Height with Chromed Speed Crank Handle Tire Changing Tools for Car Van Truck Vehicles, 1PCs US Ship
Package included: Scissor jack x 1 Handle x 1 Specification: Condition: Brand new Minimum height: about 105MM Maximum height: approximately 385MM Lifting: 2T Color: Black Material: Steel Net weight: 2.1KG Item Size: 41*8.8*9CM HEIGHT/CAPACITY CURVE This device is designed to sustain the following loads at these specified heights. DO NOT EXCEED the rated capacity for each position. Before Use 1. Check before each use for abnormal conditions such as cracked welds, leaks, damaged, loose or missing parts. 2. Inspect the jack immediately if lift is believed to have been subjected to an abnormal load or shock. 3. If the jack is found to be damaged, it should be removed from service until properly repaired. OPERATING INSTRUCTIONS 1. Insert the jack handle into the hole of the handle socket. 2. Make sure that the saddle is correctly positioned. To prevent damage to the jack, do not move the jack while the handle is intact in the socket. 3. To raise load, use one hand to hold the front part of the handle and use the other hand to turn at the rear and of the handle clockwise. 4. To lower load, use one hand to hold the front part of the handle and use the other hand to turn at the rear and of the handle counterclockwise slowly. CARE AND MAINTENANCE 1. When jack is not in use, lifting arm should be in full down position. 2. Always keep jack clean and keep the screw and bearings well lubricated. 3. Store the handle with care.
- UPC: 613852952054
- ASIN: B0746F3SVD
- Brand: DICN
- Size: Scissor Jack
- Manufacturer: DICN Factory
DICN Vehicle Scissor Jack 2 Ton/15 Inch Black Steel with Crank Handle for Toyota Ford BMW Mazda
DICN Vehicle Scissor Jack 2 Ton/15 Inch Black Steel with Crank Handle for Toyota Ford BMW Mazda
Package included: Scissor jack x 1 Handle x 1 Specification: Condition: Brand new Minimum height: about 105MM Maximum height: approximately 385MM Lifting: 2T Color: Black Material: Steel Net weight: 2.1KG Item Size: 41*8.8*9CM HEIGHT/CAPACITY CURVE This device is designed to sustain the following loads at these specified heights. DO NOT EXCEED the rated capacity for each position. Before Use 1. Check before each use for abnormal conditions such as cracked welds, leaks, damaged, loose or missing parts. 2. Inspect the jack immediately if lift is believed to have been subjected to an abnormal load or shock. 3. If the jack is found to be damaged, it should be removed from service until properly repaired. OPERATING INSTRUCTIONS 1. Insert the jack handle into the hole of the handle socket. 2. Make sure that the saddle is correctly positioned. To prevent damage to the jack, do not move the jack while the handle is intact in the socket. 3. To raise load, use one hand to hold the front part of the handle and use the other hand to turn at the rear and of the handle clockwise. 4. To lower load, use one hand to hold the front part of the handle and use the other hand to turn at the rear and of the handle counterclockwise slowly. CARE AND MAINTENANCE 1. When jack is not in use, lifting arm should be in full down position. 2. Always keep jack clean and keep the screw and bearings well lubricated. 3. Store the handle with care.
- UPC: 783057985888
- ASIN: B073J3X67C
- Brand: DICN
- Size: Scissor Jack
- Manufacturer: DICN Factory
Autofu 2 Ton Scissor Floor Jack for Car/Travel Trailer/Truck/SUV/UTV with Speed Handle Floor Jack Steel
Autofu 2 Ton Scissor Floor Jack for Car/Travel Trailer/Truck/SUV/UTV with Speed Handle Floor Jack Steel
★ Description： 1. The scissor jack, with tooth gears, can extend from 90mm(close position) to 360mm, more than enough to lift most vehicles. 2. Easy to operate using the chromed crank with speed handle. 3. Minimum height: about 90MM 4. Maximum height: approximately 360MM 5. Lifting: 2T 6. Color: Black 7. Material: Steel 8. Net weight: 2.1KG 9. Item Size: 35*8.5*8.5CM(13.78'' * 3.35'' * 3.35'') 10. Scope: Suitable for small and medium sized vehicles. ★ Package included: Scissor jack * 1 Handle * 1 ★ HEIGHT/CAPACITY CURVE This device is designed to sustain the following loads at these specified heights. DO NOT EXCEED the rated capacity for each position. ★ Before Use 1. Check before each use for abnormal conditions such as cracked welds, leaks, damaged, loose or missing parts. 2. Inspect the jack immediately if lift is believed to have been subjected to an abnormal load or shock. 3. If the jack is found to be damaged, it should be removed from service until properly repaired. ★ OPERATING INSTRUCTIONS 1. Insert the jack handle into the hole of the handle socket. 2. Make sure that the saddle is correctly positioned. To prevent damage to the jack, do not move the jack while the handle is intact in the socket. 3. To raise load, use one hand to hold the front part of the handle and use the other hand to turn at the rear and of the handle clockwise. 4. To lower load, use one hand to hold the front part of the handle and use the other hand to turn at the rear and of the handle counterclockwise slowly. ★ CARE AND MAINTENANCE 1. When jack is not in use, lifting arm should be in full down position. 2. Always keep jack clean and keep the screw and bearings well lubricated. 3. Store the handle with care.
- UPC: 606829327641
- ASIN: B06XXCZ2R5
- Brand: Autofu
- Manufacturer: Autofu
DICN Universal Spare Tire Tool Kit Wheel Lug Nut Wrench 17mm 19mm 21mm 23mm + Scissor Jack 2 Ton for Car Van Road Side Emergency
DICN Universal Spare Tire Tool Kit Wheel Lug Nut Wrench 17mm 19mm 21mm 23mm + Scissor Jack 2 Ton for Car Van Road Side Emergency
Packing includes: 1x Extendible Telescopic Wrench 2x Double Ended Chrome Vanadium Socket 1x Scissor jack(with handle) Wrench: High-torque telescopic extending car wheel nut wrench easily undoes wheel nuts High torque extending handle for easy use and extra leverage power Strong, light and compact construction Fitted with durable toughened non-slip rubber handle for extra grip and comfort Made of chrome carbon steel Supplied with 2 Double ended sockets (17/19MM) (21/23MM) Chrome Vanadium sockets Telescopic extending handle extends from 350MM to 550MM Scissor Jack: Color: Black Minimum height: about 105MM Maximum height: approximately 385MM Lifting: 2.0T Color: Black Material: Steel Net weight: 2.1KG Item Size: 41*8.8*9 (L×W×T) Included: Chromed Crank Speed Handle
- UPC: 783057999762
- ASIN: B073S4YWJT
- Brand: DICN
- Manufacturer: DICN Factory
DICN 1PCS Black Scissor Jack Steel Wind Up Leveling with Crank Handle Manual 2 Ton 4.2-15Inch Capacity High Lift - Spare Tire Changing Tools for Car Van Truck (US Ship)
DICN 1PCS Black Scissor Jack Steel Wind Up Leveling with Crank Handle Manual 2 Ton 4.2-15Inch Capacity High Lift - Spare Tire Changing Tools for Car Van Truck (US Ship)
Package included: Scissor jack x 1 Handle x 1 Specification: Condition: Brand new Minimum height: about 105MM Maximum height: approximately 385MM Lifting: 2T Color: Black Material: Steel Net weight: 2.1KG Item Size: 41*8.8*9CM HEIGHT/CAPACITY CURVE This device is designed to sustain the following loads at these specified heights. DO NOT EXCEED the rated capacity for each position. Before Use 1. Check before each use for abnormal conditions such as cracked welds, leaks, damaged, loose or missing parts. 2. Inspect the jack immediately if lift is believed to have been subjected to an abnormal load or shock. 3. If the jack is found to be damaged, it should be removed from service until properly repaired. OPERATING INSTRUCTIONS 1. Insert the jack handle into the hole of the handle socket. 2. Make sure that the saddle is correctly positioned. To prevent damage to the jack, do not move the jack while the handle is intact in the socket. 3. To raise load, use one hand to hold the front part of the handle and use the other hand to turn at the rear and of the handle clockwise. 4. To lower load, use one hand to hold the front part of the handle and use the other hand to turn at the rear and of the handle counterclockwise slowly. CARE AND MAINTENANCE 1. When jack is not in use, lifting arm should be in full down position. 2. Always keep jack clean and keep the screw and bearings well lubricated. 3. Store the handle with care.
- UPC: 613852958131
- ASIN: B0747CRNGR
- Brand: DICN
- Manufacturer: DICN Factory
Spare Tire Kit Scissor Jack with Speed Handle 2 Ton Floor Jack Wind Up Lift for Caravans/Honda Jazz/Audi / BMW/Benz / Ford/Toyota / Dodge/Chevy
Spare Tire Kit Scissor Jack with Speed Handle 2 Ton Floor Jack Wind Up Lift for Caravans/Honda Jazz/Audi / BMW/Benz / Ford/Toyota / Dodge/Chevy
Before Use: 1. Check before each use for abnormal conditions such as cracked welds, leaks, damaged, loose or missing parts. 2. Inspect the jack immediately if lift is believed to have been subjected to an abnormal load or shock. 3. If the jack is found to be damaged, it should be removed from service until properly repaired.Attention: 1. Study, understand and follow all instructions before operating this device. 2. Do not exceed rated capacity as designated by the height/capacity curve.(Sea below) 3. Use only on hard level surface. 4. Use for emergency tire changing only. 5. Never get beneath the vehicle when it is supported by the jack. 6. Activate the hazard warning flasher,turn off ignition, set parking brake, move automatic shift selector to park position. In case of a manual transmission, move gear selector into reverse position. In addition, the wheel diagonally opposite from the wheel being lifted shall be chocked in both directions. 7. Lift only on areas of the vehicle as specified by the vehicle manufacturer. 8. Follow tire changing procedure as per the vehicle manufacturer's owner's manual. 9. No alterations shall be made to this product. 10. Failure to heed these messages may result in personal injury and/or property damage. OPERATING INSTRUCTIONS 1. Insert the jack handle into the hole of the handle socket. 2. Make sure that the saddle is correctly positioned. To prevent damage to the jack, do not move the jack while the handle is intact in the socket. 3. To raise load, use one hand to hold the front part of the handle and use the other hand to turn at the rear and of the handle clockwise. 4. To lower load, use one hand to hold the front part of the handle and use the other hand to turn at the rear and of the handle counterclockwise slowly.
- UPC: 613852812303
- ASIN: B073W831NQ
- Brand: Autobaba
- Size: Scissor Jack
- Manufacturer: Autobaba
TOYOTA Genuine 09113-20050 Floor Jack Handle
TOYOTA Genuine 09113-20050 Floor Jack Handle
- ASIN: B00GKMP9A8
- Brand: TOYOTA
- Manufacturer: Toyota