Taprite T742HP Primary Double Gauge CO2 Regulator, Brass

Taprite T742HP Primary Double Gauge CO2 Regulator, Brass

WARNING: THIS PRODUCT CONTAINS ONE OR MORE CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER AND BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM. WASH HANDS AFTER HANDLING. You can use this low-pressure regulator on any CO2 tank with a CGA-320 valve. CO2 tanks have a male thread (CGA-320); these regulators have a female thread. This regulator features dual gauges to measure psi as well as the volume of CO2 in the cylinder, indicating how much CO2 is left in the cylinder and when you should have it refilled. The knob on the front is used to adjust the output pressure. The red polycarbonate bonnet will not chip, break or fade. There is a non-adjustable shut down built into the body of the regulator. The high-pressure ports have left-hand female threads to prevent their use as a low-pressure outlet. The non-removable adjusting screw is designed so that when it is turned all the way in the maximum downstream delivery pressure will not exceed 50psi, with a safety blow off at 60psi. Internal relief valve opens whenever delivery pressure exceeds set pressure by 15psi. This feature serves as a warning that the seat or diaphragm may be worn or damaged and should be replaced. Sintered metal flow control filter in the inlet nipple to prevent dirt and other particles from damaging internal regulator parts. The permanent Quad-Ring Seal on the inlet nipple helps eliminate a source of leaks, so there is no need to use a new fiber washer each time the tank is changed. Outlet features NADS 1600C shutoff which eliminates a source of gas leaks. The duck bill check valve helps prevent product back up into the regulator, a common cause of malfunction in the regulating and relief valve parts. Hose barb end designed for use with 5/16 inch I.D. pressure tubing. All regulators are pressure tested to assure in-field reliability. The seat assembly is easily replaceable, so there is no need to remove the regulator from the tank. Bullets change to: Low pressure gauge (the top gauge) indicates... [Read More]

  • UPC: 608866314523
  • ASIN: B002UZUJ22
  • Brand: Taprite
  • Manufacturer: Taprite

TapRite Separate Pressure Adjusting 2 Product CO2 Regulator

TapRite Separate Pressure Adjusting 2 Product CO2 Regulator

WARNING: THIS PRODUCT CONTAINS ONE OR MORE CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER AND BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM. WASH HANDS AFTER HANDLING. Tap two kegs at the same time and control the pressure to each of them individually. This two product two pressure CO2 regulator has two separate gauges to uniquely measure the pressure to each keg and allow you to adjust it particularly for the type of beer or beverage you are drinking. A third gauge tells you the amount of CO2 left in your tank. Regulator attaches directly to CO2 tank and has an air shut off switch for each CO2 line. Nonadjustable shut down blows off at 55-65 PSI. The polycarbonate bonnet is lighter weight and stronger than zinc bonnet regulators and it will not corrode in wet environments. No special tools are required to raise or lower the CO2 pressure. The cap knob simply pulls out so it can be turned to adjust pressure up or down then pushes back in to lock in pressure. In stock and ready to ship. Features: Tap two kegs at the same time and control the pressure to each. 0-60 Gauges measure pressure to each keg. 0-2000 Gauge measures CO2 in tank. Has air shut off switch for each CO2 line. High CO2 volumetric flow to insure continuity in product dispensing. Bonnet material is glass-filled Polycarbonate. 10 Micron filter built in to keep contaminants out of regulator. Less prone to freeze up problems. Approved by Pepsi and Coca-Cola. Specs: dimensions: 9\inchW x 7 1/2\inchH x 5 1/2\inchD.

  • UPC: 845033087556
  • ASIN: B002QAP6JC
  • Brand: Taprite
  • Size: 12"x8"x8"
  • Manufacturer: Learn To Brew

Taprite Dual Gauge CO2 Beer Regulator with MFL Check Valve Bundle

Taprite Dual Gauge CO2 Beer Regulator with MFL Check Valve Bundle

Made in the USA. Taprite Dual Gauge CO2 Beer Regulator with MFL Check Valve ( Kegconnection adds an Additional 1 year warranty to Taprite regulators.) Comes with one 1/4 inch barb, one 5/16 inch barb, one swivel nut, one white flared washer. It has an adjustment system that allows pressure to be easily adjusted by hand (no tools required). This is the most consistently accurate, and well-built regulator on the market. It stays on pressure even when your CO2 tank level goes down. UL listed. Approved for use by all major breweries. Shutoff Valve is a ball type check valve that prevents product back-up into the regulator. Solid brass body with an extra long nipple. This regulator has a shutdown safety system (blow off at 55 to 60 PSI). Permanent Quad-Ring Seal on inlet nipple helps eliminate a source of leaks. There is no need to use a new fiber washer each time the tank is changed. Assembled and tested in the USA.

  • ASIN: B00D8M5NZY
  • Brand: Kegconnection
  • Manufacturer: Taprite

Taprite Co2 Primary Beer Regulator 3741-BR New Draft Wine Soda - Dual High Pressure Gauge

Taprite Co2 Primary Beer Regulator 3741-BR New Draft Wine Soda - Dual High Pressure Gauge

(WARNING: THIS PRODUCT CAN EXPOSE YOU TO CHEMICALS, INCLUDING LEAD, WHICH IS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS AND REPRODUCTIVE HARM. FOR MORE INFORMATION PLEASE VISIT: WWW.PROP65WARNINGS.CA.GOV) Primary Beer Regulator, 1P1P, CGA320 Inlet, 5/16\\" Barb Shut off w/Check, 60 PSI and 2000 PSI Gauges

  • UPC: 731157856164
  • ASIN: B00PZM6H7S
  • Brand: Taprite
  • Manufacturer: Taprite

TAPRITE - E-T1661ST-02 SECONDARY BEER REGULATOR, 1P1P, 3/8" BARB IN/THRU, 5/16" BARB SHUT-OFF, 60LB GAUGE

TAPRITE - E-T1661ST-02 SECONDARY BEER REGULATOR, 1P1P, 3/8" BARB IN/THRU, 5/16" BARB SHUT-OFF, 60LB GAUGE

Secondary Beer Regulator, 1P1P, 3/8" Barb In/Thru, 5/16" Barb Shut-off, 60lb GaugePlug, 60# Gauge, 5/16B Shutoff (w/ck valve)

  • UPC: 792436021208
  • ASIN: B01AD2UPGS
  • Brand: Taprite
  • Manufacturer: Taprite

Taprite T752HP Two Product Dual Pressure Kegerator CO2 Regulator

Taprite T752HP Two Product Dual Pressure Kegerator CO2 Regulator

The TAPRITE ADVANTAGE Taprite regulators are built and tested in accordance with UL Standard 252 for compressed gas Regulators and UL 252A for compressed gas regulator accessories All Taprite regulator components and accessories are inspected by our Quality Department upon receipt in accordance with the requirements of MIL-STD-105E High CO volumetric flow provides continuity in product dispensing Polycarbonate bonnet will not chip, break, or fade 10 Micron Filter built in to keep contaminants out of regulator One repair kit for primary and secondary regulators. WARNING: THIS PRODUCT CONTAINS ONE OR MORE CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER AND BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM. WASH HANDS AFTER HANDLING.

  • UPC: 608938598721
  • ASIN: B0060NOX40
  • Brand: Taprite
  • Manufacturer: Taprite

Co2 Beer Regulator, Dual Body, Three Gauge, Taprite Brand by Kegconnection

Co2 Beer Regulator, Dual Body, Three Gauge, Taprite Brand by Kegconnection

This Dual Body Regulator by Kegconnection is perfect for those who want to keep different pressure on different beer styles. It is also used for those who wish to have beer and soda off the same CO2 tank. You can serve multiple kegs with this system by adding an air distributor to one or both outlets. Made in the USA Taprite Regulators are a commercial grade beer regulator that is used by professional installers in bars and restaurants all over the world. They are also available for your home brew draft beer system, so you can experience the same quality and reliability as the professionals. This is the most consistent, reliable regulators in on the market today. Includes Kegconnection's DOUBLE LENGTH WARRANTY (Click HERE to view) for Home Users! Assembled and tested in the USA! Built in accordance with UL Standard 252 and the requirements of MIL-STD-105E Built in O-ring Seal to CO2 cylinder, don't have to keep up with fiber washer! Stays on pressure even as your CO2 cylinder goes down in volume. Available in many configurations to fit your needs, including primary and secondary models. Rebuild kits are available so you can keep this regulator in service indefinitely. 10 Micron Filter built in to keep contaminants out of regulator Comes with 1/4 inch inch MFL ends on check valves. Pick 5/16 inch or 1/4 inch barbed swivel nuts depending on the size of the hose you will be using.BONUS: Kegconnection adds an Additional ONE year warranty.)

  • ASIN: B00CQ9DC5I
  • Brand: Kegconnection
  • Manufacturer: Taprite

Taprite CGR284-PT 4 Way Secondary Regulator,

Taprite CGR284-PT 4 Way Secondary Regulator,

Secondary regulators are used when you are attempting to dispense two or more kegs off of the same Co2 tank. A secondary regulator will allow you to regulate the pressure of each keg individually. This regulator has check valves built into the shut off valve to prevent backflow of liquid into the regulator body.

  • UPC: 608729691686
  • ASIN: B00DE8GTZK
  • Brand: Taprite
  • Size: 4 Way
  • Manufacturer: Taprite

Taprite 12218 1 X co2 Dual Gauge Regulator

Taprite 12218 1 X co2 Dual Gauge Regulator

WARNING: THIS PRODUCT CAN EXPOSE YOU TO CHEMICALS, INCLUDING LEAD, WHICH IS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS AND REPRODUCTIVE HARM. FOR MORE INFORMATION PLEASE VISIT: WWW.PROP65WARNINGS.CA.GOV Robust design delivers performance and reliability. Extremely durable and user friendly polycarbonate bonnets make adjustments a snap. Pull cap to adjust the pressure and push back to lock it in. High CO2 volumetric flow provides continuity in product dispensing. This primary regulator connects directly to its gas source so it's ready to rock. Recommended operating pressure should be limited to 2/3 of the gauge range for maximum accuracy. UL approved per UL252 Class IV rating for CO2. Polycarbonate bonnet will not chip, break or fade. 10 micron filter built in to keep contaminants out of regulators are used throughout the beverage industry. This regulator is the most consistently accurate and well built regulator on the market. This unit stays on pressure even when your CO2 tank level does down. Approved for use by all major beer distributors and Breweries. Shutoff Valve is a ball Type check Valve that prevents product back-flow into the regulator and tank. Solid Brass with extra long nipple. Regulator has pressure safety system (burst at 55 to 60 psi). permanent Quad ring seal on Inlet nipple helps eliminate a source of leaks. no need to use a new fiber washer each time tank is changed. Regulator will be double boxed to avoid any damage in transit

  • UPC: 610395158295
  • ASIN: B008EKR0UG
  • Brand: Taprite
  • Size: 1
  • Manufacturer: Beverage Factory

Titan Controls Carbon Dioxide (CO2) Regulator for 120V Controllers & Timers

Titan Controls Carbon Dioxide (CO2) Regulator for 120V Controllers & Timers

Compatible with Titan Controls CO2 Controllers or other 120 Volt controllers and timers. Precision accuracy flow meter - 0.5 to 15 SCF/hour. Features heavy-duty solenoid valve. High quality oil-less pressure gauge. Includes two plastic tank washers and 12 ft of CO2 dispensing line. Brass construction for long-lasting dependability and durability. 1 Amp/120 Volts/60Hz.

  • UPC: 870883009359
  • ASIN: B004MUDNKS
  • Brand: Titan Controls
  • Size: 1-(Pack)
  • Manufacturer: Sunlight Supply Inc.