Autofu Universal Scissor Jack 2 Ton Wind Up Lift Floor Jacks 14 Inch Height with Crank Speed Handle Rust-Proof for Ford F-150 Chevrolet Toyota Dodge Ram
Autofu Universal Scissor Jack 2 Ton Wind Up Lift Floor Jacks 14 Inch Height with Crank Speed Handle Rust-Proof for Ford F-150 Chevrolet Toyota Dodge Ram
The scissor jack, with tooth gears, can extend from 90mm(close position) to 360mm, more than enough to lift most vehicles. Easy to operate using the chromed crank with speed handle. Condition: Brand new Minimum height: about 90MM Maximum height: approximately 360MM Lifting: 2.0T Material: Steel Net weight: 2.1KG Item Size: 35*8.5*8.5 (L×W×T) Scope: Suitable for small and medium sized vehicles. Such as: For cars/Buick/Santana/Vietnam and other vehicles. Packing include: Scissor jack * 1 Handle * 1 HEIGHT/CAPACITY CURVE This device is designed to sustain the following loads at these specified heights. DO NOT EXCEED the rated capacity for each position. Before Use: 1. Check before each use for abnormal conditions such as cracked welds, leaks, damaged, loose or missing parts. 2. Inspect the jack immediately if lift is believed to have been subjected to an abnormal load or shock. 3. If the jack is found to be damaged, it should be removed from service until properly repaired. OPERATING INSTRUCTIONS 1. Insert the jack handle into the hole of the handle socket. 2. Make sure that the saddle is correctly positioned. To prevent damage to the jack, do not move the jack while the handle is intact in the socket. 3. To raise load, use one hand to hold the front part of the handle and use the other hand to turn at the rear and of the handle clockwise. 4. To lower load, use one hand to hold the front part of the handle and use the other hand to turn at the rear and of the handle counterclockwise slowly. CARE AND MAINTENANCE: 1. When jack is not in use, lifting arm should be in full down position. 2. Always keep jack clean and keep the screw and bearings well lubricated. 3. Store the handle with care.
- UPC: 667673316120
- ASIN: B06ZY83PLD
- Brand: Autofu
- Size: Scissor Jack
- Manufacturer: Autofu
Torin Big Red Steel Scissor Jack, 1.5 Ton (3,000 lb) Capacity
Torin Big Red Steel Scissor Jack, 1.5 Ton (3,000 lb) Capacity
The Torin Big Red steel scissor jack is 1-1/2 Tons (3,000 lbs) and can be used as a rugged replacement jack or an extra utility jack that can be stored in the trunk of your car due to its compact size. The jack has a lift range from 4-1/8" to 15-1/8" with an oversized base width of 4-1/2" that provides maximum support. This extra-wide base offers easy positioning and the folding handle delivers on-the-spot quick response and speed when you need it. Features a rugged alloyed steel construction with heavy-duty steel frame and saddle. The unit is factory tested for reliability to meet ASME standards and includes a limited 1 year manufacturer warranty.
- UPC: 615268101521
- ASIN: B004PX8BC2
- Brand: Torin
- Manufacturer: Torin
DICN Scissor Jack with Crank Handle Car Tire Repair Kit Emergency for Toyota Camry Corolla Prius Vios - 2 Ton/ 4.2-15 Inch
DICN Scissor Jack with Crank Handle Car Tire Repair Kit Emergency for Toyota Camry Corolla Prius Vios - 2 Ton/ 4.2-15 Inch
Package included: Scissor jack x 1 Handle x 1 Specification: Condition: Brand new Minimum height: about 105MM Maximum height: approximately 385MM Lifting: 2T Color: Black Material: Steel Net weight: 2.1KG Item Size: 41*8.8*9 CM HEIGHT/CAPACITY CURVE This device is designed to sustain the following loads at these specified heights. DO NOT EXCEED the rated capacity for each position. Before Use 1. Check before each use for abnormal conditions such as cracked welds, leaks, damaged, loose or missing parts. 2. Inspect the jack immediately if lift is believed to have been subjected to an abnormal load or shock. 3. If the jack is found to be damaged, it should be removed from service until properly repaired. OPERATING INSTRUCTIONS 1. Insert the jack handle into the hole of the handle socket. 2. Make sure that the saddle is correctly positioned. To prevent damage to the jack, do not move the jack while the handle is intact in the socket. 3. To raise load, use one hand to hold the front part of the handle and use the other hand to turn at the rear and of the handle clockwise. 4. To lower load, use one hand to hold the front part of the handle and use the other hand to turn at the rear and of the handle counterclockwise slowly. CARE AND MAINTENANCE 1. When jack is not in use, lifting arm should be in full down position. 2. Always keep jack clean and keep the screw and bearings well lubricated. 3. Store the handle with care.
- UPC: 783057938358
- ASIN: B073CMLYTJ
- Brand: DICN
- Manufacturer: DICN Factory
Spare Tire Kit Scissor Jack with Speed Handle 2 Ton Floor Jack Wind Up Lift for Caravans/Honda Jazz/Audi / BMW/Benz / Ford/Toyota / Dodge/Chevy
Spare Tire Kit Scissor Jack with Speed Handle 2 Ton Floor Jack Wind Up Lift for Caravans/Honda Jazz/Audi / BMW/Benz / Ford/Toyota / Dodge/Chevy
Before Use: 1. Check before each use for abnormal conditions such as cracked welds, leaks, damaged, loose or missing parts. 2. Inspect the jack immediately if lift is believed to have been subjected to an abnormal load or shock. 3. If the jack is found to be damaged, it should be removed from service until properly repaired.Attention: 1. Study, understand and follow all instructions before operating this device. 2. Do not exceed rated capacity as designated by the height/capacity curve.(Sea below) 3. Use only on hard level surface. 4. Use for emergency tire changing only. 5. Never get beneath the vehicle when it is supported by the jack. 6. Activate the hazard warning flasher,turn off ignition, set parking brake, move automatic shift selector to park position. In case of a manual transmission, move gear selector into reverse position. In addition, the wheel diagonally opposite from the wheel being lifted shall be chocked in both directions. 7. Lift only on areas of the vehicle as specified by the vehicle manufacturer. 8. Follow tire changing procedure as per the vehicle manufacturer's owner's manual. 9. No alterations shall be made to this product. 10. Failure to heed these messages may result in personal injury and/or property damage. OPERATING INSTRUCTIONS 1. Insert the jack handle into the hole of the handle socket. 2. Make sure that the saddle is correctly positioned. To prevent damage to the jack, do not move the jack while the handle is intact in the socket. 3. To raise load, use one hand to hold the front part of the handle and use the other hand to turn at the rear and of the handle clockwise. 4. To lower load, use one hand to hold the front part of the handle and use the other hand to turn at the rear and of the handle counterclockwise slowly.
- UPC: 613852812303
- ASIN: B073W831NQ
- Brand: Autobaba
- Size: Scissor Jack
- Manufacturer: Autobaba
DICN Steel Scissor Jack Black Rustproof 2 Ton Capacity/385mm Max.Height with Chromed Speed Crank Handle Tire Changing Tools for Car Van Truck Vehicles, 1PCs US Ship
DICN Steel Scissor Jack Black Rustproof 2 Ton Capacity/385mm Max.Height with Chromed Speed Crank Handle Tire Changing Tools for Car Van Truck Vehicles, 1PCs US Ship
Package included: Scissor jack x 1 Handle x 1 Specification: Condition: Brand new Minimum height: about 105MM Maximum height: approximately 385MM Lifting: 2T Color: Black Material: Steel Net weight: 2.1KG Item Size: 41*8.8*9CM HEIGHT/CAPACITY CURVE This device is designed to sustain the following loads at these specified heights. DO NOT EXCEED the rated capacity for each position. Before Use 1. Check before each use for abnormal conditions such as cracked welds, leaks, damaged, loose or missing parts. 2. Inspect the jack immediately if lift is believed to have been subjected to an abnormal load or shock. 3. If the jack is found to be damaged, it should be removed from service until properly repaired. OPERATING INSTRUCTIONS 1. Insert the jack handle into the hole of the handle socket. 2. Make sure that the saddle is correctly positioned. To prevent damage to the jack, do not move the jack while the handle is intact in the socket. 3. To raise load, use one hand to hold the front part of the handle and use the other hand to turn at the rear and of the handle clockwise. 4. To lower load, use one hand to hold the front part of the handle and use the other hand to turn at the rear and of the handle counterclockwise slowly. CARE AND MAINTENANCE 1. When jack is not in use, lifting arm should be in full down position. 2. Always keep jack clean and keep the screw and bearings well lubricated. 3. Store the handle with care.
- UPC: 613852952054
- ASIN: B0746F3SVD
- Brand: DICN
- Size: Scissor Jack
- Manufacturer: DICN Factory
15 Inch 2 Ton Scissor Lift Jacks with Handle Floor Wind Up Jack for Toyota Chevy Silverado Honda Civic Accord Ford Solid Steel US Stock
15 Inch 2 Ton Scissor Lift Jacks with Handle Floor Wind Up Jack for Toyota Chevy Silverado Honda Civic Accord Ford Solid Steel US Stock
The scissor jack, with tooth gears, can extend from 90mm(close position) to 360mm, more than enough to lift most vehicles. Easy to operate using the chromed crank with speed handle. Condition: Brand new Minimum height: about 90MM Maximum height: approximately 360MM Lifting: 2.0 Ton Material: Steel Net weight: 2.1KG Item Size: 35*8.5*8.5 (L×W×T) Scope: Suitable for small and medium sized vehicles. Such as: For cars/Buick/Santana/Vietnam and other vehicles. Packing include: Scissor jack * 1 Handle * 1
- UPC: 783057819671
- ASIN: B073SCF5DH
- Brand: ZhanGe
- Size: Scissor Jack
- Manufacturer: ZhanGe Factory
Pro-Lift B-012D Grey Hydraulic Bottle Jack - 12 Ton Capacity
Pro-Lift B-012D Grey Hydraulic Bottle Jack - 12 Ton Capacity
Great Addition to any Garage and Home Pro-Lift B-012D Grey Hydraulic Bottle Jack is a 12-ton bottle jack that is ideal for auto, truck service, farm and shop use. With the heat treated critical stress areas, it ensures long life performance. In addition, the carrying handle makes it so easy to carry around wherever need it. It features the steel lifting saddle that is engineered to hold load securely. With the extension screw, it allows Pro Lift B-012D Bottle Jack to be adjusted to accommodate desired work height. Pro Lift B-012D Bottle Jack also features Built-In bypass system to protect against ram over-travel. - Steel Lifting Saddle Engineered to Hold Load Securely - Extension Screw Adjusts to Accommodate Desired Work Height - Built-In Bypass System to Protect against Ram Over-Travel - Heat Treated Critical Stress Areas - Designed to Meet the Latest ANSI/PALD Standards Specifications - Capacity: 12 Ton - Lifting Range: 9-1/2 x 18-7/8 inch - Carrying Handle: Yes - Item Weight: 18 Lbs Pro Lift B-012D Bottle Jack is backed with SFA 90 Days Warranty from the Date of Purchase. Grab one now to add to your home tool set
- UPC: 652597013095
- ASIN: B00DGW346G
- Brand: Pro-LifT
- Size: 12 Ton
- Manufacturer: Pro-Lift
DICN Vehicle Scissor Jack 2 Ton/15 Inch Black Steel with Crank Handle for Toyota Ford BMW Mazda
DICN Vehicle Scissor Jack 2 Ton/15 Inch Black Steel with Crank Handle for Toyota Ford BMW Mazda
Package included: Scissor jack x 1 Handle x 1 Specification: Condition: Brand new Minimum height: about 105MM Maximum height: approximately 385MM Lifting: 2T Color: Black Material: Steel Net weight: 2.1KG Item Size: 41*8.8*9CM HEIGHT/CAPACITY CURVE This device is designed to sustain the following loads at these specified heights. DO NOT EXCEED the rated capacity for each position. Before Use 1. Check before each use for abnormal conditions such as cracked welds, leaks, damaged, loose or missing parts. 2. Inspect the jack immediately if lift is believed to have been subjected to an abnormal load or shock. 3. If the jack is found to be damaged, it should be removed from service until properly repaired. OPERATING INSTRUCTIONS 1. Insert the jack handle into the hole of the handle socket. 2. Make sure that the saddle is correctly positioned. To prevent damage to the jack, do not move the jack while the handle is intact in the socket. 3. To raise load, use one hand to hold the front part of the handle and use the other hand to turn at the rear and of the handle clockwise. 4. To lower load, use one hand to hold the front part of the handle and use the other hand to turn at the rear and of the handle counterclockwise slowly. CARE AND MAINTENANCE 1. When jack is not in use, lifting arm should be in full down position. 2. Always keep jack clean and keep the screw and bearings well lubricated. 3. Store the handle with care.
- UPC: 783057985888
- ASIN: B073J3X67C
- Brand: DICN
- Size: Scissor Jack
- Manufacturer: DICN Factory
DICN Car Scissor Jack Lift Leveling with Crank Handle Roadside Emergency for Honda Civic/Accord/CR-V/Element/Odyssey/Pilot, 2-Ton Max. 360mm Work Height
DICN Car Scissor Jack Lift Leveling with Crank Handle Roadside Emergency for Honda Civic/Accord/CR-V/Element/Odyssey/Pilot, 2-Ton Max. 360mm Work Height
Package included: Scissor jack x 1 Handle x 1 Specification: Condition: Brand new Minimum height: about 90MM Maximum height: approximately 360MM Lifting: 2T Color: Black Material: Steel Net weight: 2.1KG Item Size: 35*8.5*8.5CM HEIGHT/CAPACITY CURVE This device is designed to sustain the following loads at these specified heights. DO NOT EXCEED the rated capacity for each position. Before Use 1. Check before each use for abnormal conditions such as cracked welds, leaks, damaged, loose or missing parts. 2. Inspect the jack immediately if lift is believed to have been subjected to an abnormal load or shock. 3. If the jack is found to be damaged, it should be removed from service until properly repaired. OPERATING INSTRUCTIONS 1. Insert the jack handle into the hole of the handle socket. 2. Make sure that the saddle is correctly positioned. To prevent damage to the jack, do not move the jack while the handle is intact in the socket. 3. To raise load, use one hand to hold the front part of the handle and use the other hand to turn at the rear and of the handle clockwise. 4. To lower load, use one hand to hold the front part of the handle and use the other hand to turn at the rear and of the handle counterclockwise slowly. CARE AND MAINTENANCE 1. When jack is not in use, lifting arm should be in full down position. 2. Always keep jack clean and keep the screw and bearings well lubricated. 3. Store the handle with care.
- UPC: 734010482500
- ASIN: B071FZJT4S
- Brand: DICN
- Manufacturer: DICN Factory
YEHAM Metal Steel Car Truck Jack Lug Handle Wrench Auto Repair Tool
YEHAM Metal Steel Car Truck Jack Lug Handle Wrench Auto Repair Tool
Package include:1 x Jack Handle (The scissor lift jack is NOT included) Material: Steel body & plastic handle Size: 15.5 x 6 x 0.1 inches Color: yellow / black Weight: 12oz / 340g Note:When jack is not in use,the two parts of Crank handle should be closed together state,folding storage
- UPC: 709202984698
- ASIN: B01N0UVMYE
- Brand: YEHAM
- Manufacturer: YM